Search Results

Natural gas quality, in terms of the volume fraction of higher hydrocarbons, strongly affects the auto-ignition characteristics of the air-fuel mixture, the engine performance and its controllability. The influence of natural gas composition on engine operation has been investigated both experimentally and through chemical kinetic based cycle simulation. A range of two component gas mixtures has been tested with methane as the base fuel. The equivalence ratio (0.3), the compression ratio (19.8), and the engine speed (1000 rpm) were held constant in order to isolate the impact of fuel autoignition chemistry. For each fuel mixture, the start of combustion was phased near top dead center (TDC) and then the inlet mixture temperature was reduced. These experimental results have been utilized as a source of data for the validation of a chemical kinetic based full-cycle simulation.

This paper discusses the compression ratio influence on maximum load of a Natural Gas HCCI engine. A modified Volvo TD100 truck engine is controlled in a closed-loop fashion by enriching the Natural Gas mixture with Hydrogen. The first section of the paper illustrates and discusses the potential of using hydrogen enrichment of natural gas to control combustion timing. Cylinder pressure is used as the feedback and the 50 percent burn angle is the controlled parameter. Full-cycle simulation is compared to some of the experimental data and then used to enhance some of the experimental observations dealing with ignition timing, thermal boundary conditions, emissions and how they affect engine stability and performance. High load issues common to HCCI are discussed in light of the inherent performance and emissions tradeoff and the disappearance of feasible operating space at high engine loads.

The effects of lubricating oil on friction and engine-out emissions in a light-duty 2.2L compression ignition direct injection (CIDI) engine were investigated. A matrix of test oils varying in viscosity (SAE 5W-20 to 10W-40), friction modifier (FM) level and chemistry (MoDTC and organic FM), and basestock chemistry (mineral and synthetic) was investigated. Tests were run in an engine dynamometer according to a simulated, steady state FTP-75 procedure. Low viscosity oils and high levels of organic FM showed benefits in terms of fuel economy, but there were no significant effects observed with the oils with low MoDTC concentration on engine friction run in this program. No significant oil effects were observed on the gaseous emissions of the engine. PM emissions were analyzed for organic solubles and insolubles. The organic soluble fraction was further analyzed for the oil and fuel soluble portions.

To better understand the factors affecting soot formation in diesel engines, in-cylinder soot and diffusion flame lift-off were measured in a heavy-duty, direct-injection diesel engine. Measurements were obtained at two operating conditions using two commercial diesel fuels and a range of oxygenated paraffinic fuel blends. A line-of-sight laser extinction diagnostic was improved and employed to measure the relative soot concentration within the jet (“jet-soot”) and the rates of soot-wall deposition on the piston bowl-rim. An OH chemiluminescence imaging technique was developed to determine the location of the diffusion flame and to measure the lift-off lengths of the diffusion flame to estimate the amount of oxygen entrainment in the diesel jets. Both the jet-soot and the rate of soot-wall deposition were found to decrease with increasing fuel oxygen-to-carbon ratio (O/C) over a wide range of O/C.

Charge boosting strategy plays an essential role in improving the power density of diesel engines while meeting stringent emissions regulations. In downsized two-stage turbocharged engines, turbocharger matching is critical to achieve desired boost pressure while maintaining sufficiently fast transient response. A numerical simulation model is developed to evaluate the effect of two-stage turbocharger configurations on the perceived vehicle acceleration. The simulation model developed in GT-SUITE consists of engine, drivetrain, and vehicle dynamics sub-models. A model-based turbocharger control logic is developed in MATLAB using an analytical compressor model and a mean-value engine model. The components of the two-stage turbocharging system evaluated in this study include a variable geometry turbine in the high-pressure stage, a compressor bypass valve in the low-pressure stage and an electrically assisted turbocharger in the low-pressure stage.

A program to explore the effects of natural and additive-derived cetane on various aspects of diesel performance and combustion has been carried out. Procedures have been developed to measure diesel engine fuel consumption and power to a high degree of precision. These methods have been used to measure fuel consumption and power in three heavy-duty direct-injection diesel engines. The fuel matrix consisted of three commercial fuels of cetane number (CN) of 40-42, the same fuels raised to CN 48-50 with a cetane improver additive, and three commercial fuels of base CN 47-50. The engines came from three different U.S. manufacturers and were of three different model years and emissions configurations. Both fuel economy and power were found to be significantly higher for the cetane-improved fuels than for the naturally high cetane fuels. These performance advantages derive mainly from the higher volumetric heat content inherent to the cetane-improved fuels.

Exhaust gas rebreathing is considered to be a practical enabler that could be used in HCCI production engines. Recent experimental work at the University of Michigan demonstrates that the combustion characteristics of an HCCI engine using large amounts of hot residual gas by rebreathing are very sensitive to engine thermal conditions. This computational study addresses HCCI engine operation with rebreathing, with emphasis on the effects of engine thermal conditions during transient periods. A 1-D cycle simulation with thermal networks is carried out under load and speed transitions. A knock integral auto-ignition model, a modified Woschni heat transfer model for HCCI engines and empirical correlations to define burn rate and combustion efficiency are incorporated into the engine cycle simulation model. The simulation results show very different engine behavior during the thermal transient periods compared with steady state.

Chemiluminescence imaging has been applied to investigate the naturally occurring charge stratification in an HCCI engine. This stratification slows the pressure-rise rate (PRR) during combustion, making it critical to the high-load operating limit of these engines. Experiments were conducted in a single-cylinder HCCI engine modified with windows in the combustion chamber for optical access. Using this engine, chemiluminescence images were obtained from three different view angles. These included both single-shot images with intensified CCD cameras and high-speed (20kHz) sequences with an intensified CMOS video camera. The engine was fueled with iso-octane, which has been shown to be a reasonable surrogate for gasoline and exhibits only single-stage ignition at these naturally aspirated conditions. The chemiluminescence images show that the HCCI combustion is not homogeneous but has a strong turbulent structure even when the fuel and air are fully premixed prior to intake.

Modern diesel engines operate under injection pressures varying from 30 to 200 MPa and employ combinations of very early and conventional injection timings to achieve partially homogeneous mixtures. The variety of injection and cylinder pressures results in droplet atomization under a wide range of Weber numbers. The high injection velocities lead to fast jet disintegration and secondary droplet atomization under shear and catastrophic breakup mechanisms. The primary atomization of the liquid jet is modeled considering the effects of both infinitesimal wave growth on the jet surface and jet turbulence. Modeling of the secondary atomization is based on a combination of a drop fragmentation analysis and a boundary layer stripping mechanism of the resulting fragments for high Weber numbers. The drop fragmentation process is predicted from instability considerations on the surface of the liquid drop.

This study investigates the impact of transient engine operation on the emissions formed during a tip-in procedure. A medium-duty production V-8 diesel engine is used to conduct experiments in which the rate of pedal position change is varied. Highly-dynamic emissions instrumentation is implemented to provide real-time measurement of NOx and particulate. Engine subsystems are analyzed to understand their role in emissions formation. As the rate of pedal position change increases, the emissions of NOx and particulates are affected dramatically. An instantaneous load increase was found to produce peak NOx values 1.8 times higher and peak particulate concentrations an order of magnitude above levels corresponding to a five-second ramp-up. The results provide insight into relationship between driver aggressiveness and diesel emissions applicable to development of drive-by-wire systems. In addition, they provide direct guidance for devising low-emission strategies for hybrid vehicles.

A flamelet model is used to calculate combustion in a diesel engine, and the results are compared to experimental data available from an optically accessible, direct-injection diesel research engine. The 3∼D time-dependent Kiva-II code is used for the calculations, the standard Arrhenius combustion model being replaced by an ignition model and the coherent flame model for turbulent combustion. The ignition model is a four-step mechanism developed for heavy hydrocarbons which has been previously used for diesel combustion. The turbulent combustion model is a flamelet model developed from the basic ideas of Marble and Broadwell. This model considers local regions of the turbulent flame front as interfaces called flamelets which separate fuel and oxidizer in the case of a diffusion flame. These flamelets are accounted for by solving a transport equation for the flame surface density, i.e., the flame area per unit volume.

This paper describes the concept and a practical implementation of piston-compounding. First, a detailed computer simulation of the piston-compounded engine is used to shed light into the thermodynamic events associated with the operation of this engine, and to predict the performance and fuel economy of the entire system. Starting from a baseline design, the simulation is used to investigate changes in system performance as critical parameters are varied. The latter include auxiliary cylinder and interconnecting manifold volumes for a given main cylinder volume, auxiliary cylinder valve timings in relation to main cylinder timings, and degree of heat loss to the coolant. Optimum designs for either highest power density or highest thermal efficiency (54%) are thus recommended. It is concluded that a piston-compounded adiabatic engine concept is a promising future powerplant.

Two-dimensional laser-sheet imaging and high-speed cinematography have been used to examine the combustion process in a newly constructed, optically accessible, direct-injection Diesel engine of the “heavy-duty” size class. The design of this engine preserves the intake port geometry and basic dimensions of a Cummins N-series production engine. It also includes several unique features to provide considerable optical access. An extended piston with piston-crown window and a window in the cylinder head allow the processes in the combustion bowl and squish region to be observed simultaneously. Windows at the top of the cylinder wall provide orthogonal-optical access with the capability of allowing the laser sheet to enter the cylinder along the axis of the spray. Finally, this new engine incorporates a unique separating cylinder liner that permits rapid cleaning of the windows. Studies were performed at a medium speed (1200 rpm) using a Cummins closed-nozzle fuel injector.

The finite volume, three-dimensional, turbulent flow code ARIS-3D is applied to the study of the complex flow field through the inlet port and within the cylinder of a uniflow-scavenged engine. The multiblock domain decomposition technique is used to accommodate this complex geometry. In this technique, the domain is decomposed into two blocks, one block being the cylinder and the other being the inlet duct. The effects of inlet duct length, geometric port swirl angle, and number of ports on swirl generating capability are explored. Trade-offs between swirl level and inherent pressure drop can thus be identified, and inlet port design can be optimized.

A novel framework for intelligent design of engine systems is introduced. Existing models of engine components and processes are integrated into a multi-purpose, flexible configuration framework. Fundamental thermodynamic elements, including zero-dimensional control volumes, one-dimensional pulsating fluid lines, and continuous flow machines are identified as the constituting components of engine systems. Models of the behavior of these elements, with various degrees of thermodynamic resolution, have been implemented into the framework. The task of the engine designer is, thus, reduced into selecting appropriate thermodynamic elements to model his engine system based on his design objectives. The applicability of the present framework to a wide range of simulation problems is demonstrated.

An experimental study was conducted to investigate the effects of elevated piston temperature on deposit growth patterns in a spark-ignition (SI) engine. A series of thermocouple-instrumented, insulated piston designs was developed for controlling and in-situ monitoring of deposit growth on the piston surface. Upon stabilization of deposit growth, a physical and chemical analysis of deposits from different locations was conducted. It was shown that localized deposit growth correlated strongly with rates of change of temperature at the same locations. At the end of an accelerated 18-hour test schedule using a premium unleaded fuel without reformer bottoms, a 4 μm reduction in average deposit thickness was achieved by elevating the piston surface temperature from 215 °C to 264 °C. No measurable deposit growth was obtained when operating with a critical wall surface temperature of 320 °C and the base unleaded fuel.

Five small two-stroke engine designs were tested at different air/fuel ratios, under steady state and transient cycles. The effects of combustion chamber design, carburetor design, lean burning, and fuel composition on performance, hydrocarbon and carbon monoxide emissions were studied. All tested engines had been designed to run richer than stoichiometric in order to obtain satisfactory cooling and higher power. While hydrocarbon and carbon monoxide emissions could be greatly reduced with lean burning, engine durability would be worsened. However, it was shown that the use of a catalytic converter with acceptably lean combustion was an effective method of reducing emissions. Replacing carburetion with in-cylinder fuel injection in one of the engines resulted in a significant reduction of hydrocarbon and carbon monoxide emissions.

A comprehensive quasi-dimensional computer simulation of the spark-ignition (SI) engine was used to explore part-load, fuel economy benefits of the Variable Stroke Engine (VSE) compared to the conventional throttled engine. First it was shown that varying stroke can replace conventional throttling to control engine load, without changing the engine characteristics. Subsequently, the effects of varying stroke on turbulence, burn rate, heat transfer, and pumping and friction losses were revealed. Finally these relationships were used to explain the behavior of the VSE as stroke is reduced. Under part load operation, it was shown that the VSE concept can improve brake specific fuel consumption by 18% to 21% for speeds ranging from 1500 to 3000 rpm. Further, at part load, NOx was reduced by up to 33%. Overall, this study provides insight into changes in processes within and outside the combustion chamber that cause the benefits and limitations of the VSE concept.

An early-design methodology for predicting both expected fuel economy and catalyst-out CO, HC and NOx concentrations during arbitrarily-defined transient cycles is presented. The methodology is based on utilizing a vehicle-powertrain model with embedded maps of fully warmed up engine-out performance and emissions, and appropriate temperature-dependent correction factors to account for not fully warmed up conditions during transients. Similarly, engine-out emissions are converted to catalyst-out emissions using conversion efficiencies based on the catalyst brick temperature. A crucial element of the methodology is hence the ability to predict heat flows and component temperatures in the engine and the exhaust system during transients, consistent with the data available during concept definition and early design phases.

Piston heat transfer measurements were taken under varying knock intensity in a modern spark-ignition engine combustion chamber. For a range of knocking spark timings, two knock intensity levels were obtained by using a high (80°C) and a low (50°C) cylinder head coolant temperature. Data were taken with a central and a side spark plug configuration. When the spark-plug was placed at the center of the combustion chamber, a linear variation of peak heat flux with knock intensity was found in the end-gas region. Very large changes in peak heat flux (on the order of 100%) occurred at probes whose relative location with respect to the end gas zone changed from being within (80°C coolant case) to being outside the zone (50°C coolant case). With side spark-plug, distinct differences in peak heat flux occurred at all probes and under all knock intensities, but the correlation between knock intensity and heat flux was not linear.